Cisco's rigorous and proprietary process ensures that our customers get genuine Cisco products, certified by Cisco. Manufacturer Refurbished - Cisco Refresh products have been remanufactured, have had critical engineering change orders made, and have been thoroughly tested and retested to meet stringent Cisco specifications. It presents a 10 ft (3m) length and best fit for Cisco 1700, 1720, 805, and AS5300 Routers. Get information now.The Cisco V35 Cable DTE Male to Smart Serial 10ft CAB-SS-V35MT-RF is a spare V35 DTE cable with 26 pin Smart Serial - male connector and 34 pin M/34 (V.35) - male connector on other end order to connect the router to the serial devices in your network. Where can i buy plaquenil without a prescription in USĪctual what you want to know about drug. !- The above commands are part of a broader Dial-on-Demand Routing (DDR) Maui-soho-01(config-if)# async default routing Maui-soho-01(config-if)# async mode interactive !- Continue to configure this serial interface just as you !- Places the interface in asynchronous mode.
Maui-soho-01(config-if)# physical-layer async Maui-soho-01(config)# interface Serial 2/0 Here is a section of an asynchronous configuration: Issue the physical-layer async command in order to configure the module for asynchronous communication. The default setting for this module is synchronous. Use an optical isolator (best protection). Use a data surge protector that protects against surges over +/- 18v. You can minimize this electrostatic discharge in these ways: The WIC-2A/S can be damaged by excessive electrostatic discharge. The NM-1E2W, NM-1E1R2W, and NM-2E2W network modules do not have enough performance to support the WIC-2A/S.
Note: The Cisco 1600 series is not capable of supporting the WIC-2A/S due to the lack of Serial Communications Controllers.
Synchronous support with a maximum speed of 128 Kbps.Ĭisco IOS Software versions 12.0(7)XK, 12.1(1)T, 12.2, 12.2T If you need to run at speeds lower than 600 bps, use the AUX port instead. The WIC-2A/S provides two serial ports using the Smart Serial connector.Īysnchronous support with a maximum speed of 115.2 Kbps and a minimum of 600 bps. WIC-2A/S-Two-Port Asynchronous/Synchronous WIC Features Refer to Cisco Technical Tips Conventions for more information on document conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment. The information in this document is based on the WIC-2A/S. There are no specific requirements for this document. Two cables are required to support the two ports on the WIC. This feature provides easy configuration and reconfiguration as network requirements change, without the need of purchasing a different serial interface card.
This includes: V.35, RS-232, RS-449, RS-530, RS-530A in male and female versions for both DTE and DCE devices. These dual-serial port WICs feature Cisco's new, compact, Smart Serial connectors to support a wide variety of electrical interfaces when used with the appropriate transition cable. This WIC supports mixed asynchronous and synchronous operation on a single card as well. Each port on a WIC is a different physical interface and can support different protocols such as Point-to-Point Protocol (PPP) or Frame Relay and Data Terminal Equipment/Data Communications Equipment (DTE/DCE). The low serial speed WIC-2A/S supports up to 128 Kbps synchronous or 115.2 Kbps asynchronous serial links. The dual-serial port WAN Interface Card (WIC-2A/S) provides higher levels of serial port density for a single WIC and is supported on the Cisco 1700, 2600, and 3600 series. Description: V.35 Cable, DTE Male to Smart Serial, 10 Feet Introduction